Building the future of audio production through engineering, community, & education.
178K+ subscribers

Creating an EDM Mastering Chain in 10 Steps


Get a FREE Mastered Sample of Your Song ➜


Mid-Side Equalization

Let’s start the chain with mid-side equalization - I’ll cut some of the low frequencies from the side image, then boost around 200Hz, or where I found some important low-order harmonics. Lastly, for the side image, I boosted the highs with a shelf, making them wider.

On the mid image, I amplified the fundamental of the kick, dipped a small amount of 250Hz to help higher frequencies sound louder, and boosted 3kHz for the same reason.

The frequencies and Q values you pick will probably vary slightly, but this should be a good starting point. Let’s take listen to a full A B of the unmastered and mastered tracks, using peak normalization to make them easier to compare.

Watch video example

Split EQ and Panning

I inserted this SplitEQ by Eventide and amplified the lows, high mids, and highs, using the transient and tonal bands shown in green and blue respectively. Once I found how much I wanted to amplify, I opened up the panning section to introduce mid-side panning.

Notice that on the lows I centered the transients, on the high mids I subtly widened the tone, and on the highs, I centered the transients and widened the tone band a good amount.

This greatly increased the impact of the kick, while helping me find a good balance between width and transient detail in the highs.

Let’s take a listen, and let me know if the comments if you can hear a difference.

Watch video example

Mid-Side Resonance Reduction

I used this resonance reducer to subtly balance the frequency spectrum - you can put this processor later in the chain to help reduce some of the resonances caused by your processing, but I found it worked well earlier in the chain. Notice, I kept the kick from triggering the processor.

Then I got very subtle attenuation from the rest of the frequency spectrum and blended the effect in with the mix dial. Let’s take a listen, and let me know if you think it sounds a little more balanced.

Watch video example

Bringing Up Details

I went through a few upward processors, and found that this inflator sounded the best for this particular mix - I used an aggressive effect percentage, but then compensated for that by lowering the input slightly. I found the band split setting with a slightly higher curve sounded best to me.

That said, be sure to use your ear and find the processor and settings you enjoy the most.

Let’s take a listen, and notice how the track becomes fuller.

Watch video example

Exciting High Frequencies

At this point, I felt the highs were lacking, so I used this free Fresh Air plugin to amplify 2 high shelf filters, as well as add harmonics to the high frequencies. I used slightly more aggressive settings than I typically would since I felt the track called for it.

Let’s take a listen, and notice how the plugin creates a noticeably brighter, more detailed high-frequency range.

Watch video example

Mid-Frequency Upward Bus

Using a bus and an auxiliary track, I first used a linear phase EQ to isolate the mid image of the mid - I set this to include a good combination of the low mids to high mids, but include what you feel sounds best. Then, I inserted this upward compressor.

With it, I decreased the dynamic range from the noise floor up, and from the peaks down to create a really dense sound, before bending it in with the aux track’s channel fader.

Let’s listen, and let me know if you think this creates a more dense, and upfront sound.

Watch video example

Omnipressor on Output

I was worried this processor wouldn’t fit the genre, since it seems more geared toward rock, however, it worked perfectly for increased the kick’s impact, and controlling dynamics. It both compresses and expands whenever the signal is above or below the threshold, causing a great controlled dynamic range.

Since we’re mastering I used subtle ranges, and a low ratio, but still notice a big impact on the track’s perceived loudness and punchiness. Let’s take a listen.

Watch video example

Hard Clipping to Transients

Before I start my limiting stages I want to clip the transients, just enough to cause some white noise whenever they cross the threshold. This way, the transients are controlled; however, the white noise makes them sound as if they’re still present - letting me use more limiting later on.

Let’s listen, and let me know if the transients sound a little brighter to you.

Watch video example

Limiting Stage 1

For the first limiting stage, let’s use this Oxford limiter with a fast attack, fast release, no dithering, no auto gain compensation, and about 25% of the enhance function dialed in. This enhance function in particular brings up quiet details, including any white noise added from clipping.

Let’s listen and notice how the track sounds fuller and more aggressive, and how we achieve loudness without the need for aggressive peak attenuation.

Watch video example

Limiting Stage 2

When mastering EDM, I like to use a second limiter to introduce either a dynamic or transient enhancing algorithm. This way, I can increase the loudness slightly, and keep the impact of the dynamics - in this instance I used some oversampling, no lookahead, and a quick attack and release.

Also, I chose to de-link the left and right channels, causing attenuation to them separately - I like this option whenever I’ve used heavy limiting since it brings a little life and variation back into the track.

Lastly, I brought this master up to about -6.5 to -6 LUFS, as is pretty standard with EDM, but feel free to make yours a little louder or quieter as you see fit.

Let’s listen to the full before and after one more time, to see where we started and where we ended up.

Watch video example


Get a FREE Mastered Sample of Your Song ➜



Sage Audio Membership

Make Pro Songs

Welcome to Sage Audio — where we’ve been providing top-tier studio mastering services and audio education for over two decades now. We understand the challenges of achieving that elusive "professional" sound and are committed to helping you attain it in your own mixes and masters.

That’s why we created the Sage Audio Membership™.

Just for signing up, you receive 10 free mastered songs per month with your own dedicated mastering engineer, unlimited mixing feedback, and access to Sage Audio University™ mixing and mastering courses - which include start-to-finish walkthrough sessions for various genres and 35 multitrack sessions for hands-on practice.

This platform is supported by our thriving community and tight-knit network of audio engineers. Every day, we see and hear great wins in the membership from both new and seasoned engineers, noticing a huge improvement in their mixes and masters after joining.

There are 6 unique value-points inside the Sage Audio membership, so let’s go over each one so you can decide if it’s the right fit for you.

1. 10 Free Mastered Songs Per Month

2. Unlimited Mixing Feedback

3. Sage Audio University™ (SAU) — (Mixing and Mastering Education Platform)

4. Sage Audio Community

5. 700+ In-depth Sage Audio Mixing and Mastering Videos

6. 70+ GB of Curated Sage Audio Downloadable Content, Including:


Join the Membership with a 70% Lifetime Discount = $15 /month.

See you inside,
— Sage